- Home Style Daily
- Small Upgrades
- Refresh tired window trim with caulk and paint
Refresh tired window trim with caulk and paint
Refresh your interior window trim in a single afternoon. Learn how to clean the wood, apply fresh caulk, and brush on a smooth coat of new paint.
Ideas from Vaughn Trimble

Fresh paint and crisp caulk turn tired interior window trim into a sharp feature. You can prep and paint the wood around a single window in one afternoon for the cost of a few basic supplies. A little patience and the right preparation give you a smooth finish.
Inspect the trim to see what it needs
Start with a close look at the wood. Interior window trim takes a heavy beating from daily sunlight and cold drafts. Run your bare hand over the flat window sill. This lower ledge catches condensation from the glass and bakes in the afternoon sun.
This often makes the sill the first spot to show peeling paint and water damage. Check the vertical side casings next. Look closely for old nail holes left behind by discarded curtain rods. Feel the wood for dents from moving furniture.
A smooth final coat of paint requires a flat surface underneath. Press firmly along the long seam where the wood meets the painted drywall. Seasonal temperature changes cause the wood to expand and contract. This movement can crack the old caulk.
Look for dark gaps along the outer edges of the frame. Note any areas where the existing paint is chipping or fading into a dull yellow.
A quick inspection tells you exactly what tools to grab. Minor dents require a simple wood filler. Wide gaps along the wall call for a fresh tube of acrylic latex caulk. Jot down a quick list of the damaged spots so you can grab the right supplies.
Gather these supplies before you begin:
- A damp sponge and mild liquid dish soap
- Fine 220-grit sandpaper and a tack rag
- Wood filler and a stiff metal putty knife
- A tube of paintable acrylic latex caulk and a caulk gun
- Blue painter's tape and a canvas drop cloth
- Wood primer and semigloss interior paint
- An angled synthetic paint brush
Clean the wood and lightly scuff the surface
New paint peels right off dirty wood. Wash the trim thoroughly with a damp sponge and a few drops of mild liquid dish soap. Scrub away the dusty buildup on the top ledge and wipe away the greasy fingerprints near the window locks.
Rinse your sponge in clean water. Wipe the wood down one more time to remove any soapy residue. Let the surface dry completely before you reach for the sandpaper.
Before you smooth out the rough spots, check the age of your house. The EPA lead renovation rule covers homes built before 1978 and generally does not apply to homeowners working in their own homes. Still, handle older finishes with respect.
For small areas of damaged paint in older homes, the EPA advises fixing them without sanding where possible, and wetting the area first if sanding cannot be avoided. Skipping dry sanding helps keep hazardous dust out of your living space.
If you live in a newer home, grab a sheet of fine 220-grit sandpaper. Lightly scuff the glossy areas of the trim by hand. You only need to dull the shine. Do not remove the old color completely.
This lightly rough surface gives the new primer a strong texture to grip. Avoid power sanders for this job. They quickly chew through the sharp profiles and curved edges of decorative molding.
Wipe the sanding dust away immediately. Use a slightly damp microfiber cloth to lift the fine powder off the wood. A sticky tack rag also works well. Even a thin layer of dust stops new paint from adhering properly.
Fill gaps, patch nail holes and caulk the joints
Smooth out the flat surfaces before you tackle the long edges. Press a high-quality wood filler into empty nail holes using a stiff metal putty knife. Push the filler deep into the hole to prevent trapped air bubbles. Leave a slight mound of filler over the repair.

The wet material shrinks slightly as it dries. Wait for the wood filler to dry completely hard. Lightly sand the patched spots flat. They should blend into the surrounding wood.
Run your fingers over the patch. Sand it a little more if you can feel the transition between the wood and the filler.
Fresh caulk makes the dark gaps between the trim and the wall disappear. Load a tube of paintable acrylic latex caulk into a drip-free caulk gun. Cut the plastic tip off at a sharp 45-degree angle with a utility knife. Keep the opening small.
A small opening helps you easily control the flow of the caulk. Run a thin bead down the long seam. Wet your index finger and drag it lightly over the fresh line. This gentle pressure pushes the soft material deep into the crack.
It leaves a smooth, curved finish. Keep a damp rag in your free hand. Wipe the sticky excess caulk off your finger after every single pass.
A tight, clean edge is a great example of small home upgrades you notice every single day. Let the new caulk cure as long as the tube says before you start painting. Wet caulk ruins a paint brush and leaves ugly smears on the wall.
Protect the glass, prime bare spots and paint the trim
Preparation keeps your final paint job crisp. Tape saves you from scraping dry paint off the windowpane tomorrow morning. Run a continuous strip of blue painter's tape along the glass right against the wood. Press the inner edge down firmly with a flexible putty knife.
This stops wet paint from bleeding underneath. Spread a heavy canvas drop cloth on the floor directly beneath the window. Canvas absorbs accidental paint drips. Plastic sheets leave the wet paint sitting on top to ruin your shoes.
Add a strip of tape to the painted wall edge if you lack a steady hand. Taking the time to mask the area properly removes the stress from the rest of the job.
Bare wood and freshly patched spots require a protective coat of primer. Brush a thin layer of quality wood primer over the dried filler. Apply primer to any worn edges on the sill. Primer grips the bare patches tightly.
It stops old wood stains from bleeding through your new finish. Let the primer dry as long as the can says.
Paint the wood with a small angled brush designed for trim work. Dip just the bottom third of the synthetic bristles into the paint can. Tap the brush against the inside rim. This drops the heavy excess back into the can.
Brush the paint onto the trim in long sweeps that follow the natural grain of the wood. Semigloss paint suits interior trim. It reflects a soft amount of light and wipes clean easily.
This durable finish suits a busy window over the kitchen sink where water splashes happen often. Apply a thin, even coat rather than brushing the paint on heavily. Thick paint drips down the vertical side casings. It often pools in the bottom corners of the sill.
Peel the painter's tape off the glass while the final coat is still slightly wet. Pull the tape back over itself at a sharp angle. Move at a slow, steady pace. Removing the tape while the paint remains tacky gives you a sharp line.
It prevents the new finish from peeling away with the adhesive. Let the paint dry overnight before you close the window or rehang your blinds.